- 您现在的位置：买卖IC网 > Sheet目录471 > MAX1473EVKIT-433 (Maxim Integrated)EVAL KIT MAX1473
MAX1473
315MHz/433MHz ASK Superheterodyne
Receiver with Extended Dynamic Range
C 7 =
C 6 =
b
a ( 100 k )( π ) ( f c )
a
4 ( 100 k )( π ) ( f c )
Data Slicer
The purpose of the data slicer is to take the analog out-
put of the data filter and convert it to a digital signal.
This is achieved by using a comparator and comparing
the analog input to a threshold voltage. One input is
supplied by the data filter output. Both comparator
inputs are accessible off chip to allow for different
where f C is the desired 3dB corner frequency.
For example, choose a Butterworth filter response with
a corner frequency of 5kHz:
methods of generating the slicing threshold, which is
applied to the second comparator input.
The suggested data slicer configuration uses a resistor
(R1) connected between DSN and DSP with a capaci-
C 7 =
1 . 000
( 1 . 414 )( 100 k ? )( 3 . 14 )( 5 kHz )
≈ 450 pF
tor (C8) from DSN to DGND (Figure 2). This configura-
tion averages the analog output of the filter and sets the
threshold to approximately 50% of that amplitude. With
Choosing standard capacitor values changes C7 to
470pF and C6 to 220pF, as shown in the Typical
Application Circuit.
MAX1473
RSSI
this configuration, the threshold automatically adjusts
as the analog signal varies, minimizing the possibility
for errors in the digital data. The sizes of R1 and C8
affect how fast the threshold tracks to the analog ampli-
tude. Be sure to keep the corner frequency of the RC
circuit much lower than the lowest expected data rate.
Note that a long string of zeros or 1’s can cause the
threshold to drift. This configuration works best if a cod-
ing scheme, such as Manchester coding, which has an
equal number of zeros and 1’s, is used.
R DF2
100k ?
R DF1
100k ?
To prevent continuous toggling of DATAOUT in the
absence of an RF signal due to noise, hysteresis can
be added to the data slicer as shown in Figure 3.
19
DFO
C6
21
OPP
C7
22
DFFB
For further information on Data Slicer options, please
refer to Maxim Application Note 3671, Data Slicing
Techniques for UHF ASK Receivers.
Figure 1. Sallen-Key Lowpass Data Filter
MAX1473
DATA
SLICER
MAX1473
DATA
25
23
20
19
SLICER
DATAOUT
DSP
DSN
R1
DFO
R2
R3
25
DATAOUT
C8
20
DSN
R1
23
DSP
19
DFO
R*
*OPTIONAL
C8
Figure 2. Generating Data Slicer Threshold
Maxim Integrated
Figure 3. Generating Data Slicer Hysteresis
11
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX1479EVKIT-315
EVAL KIT FOR MAX1479 315MHZ
MAX19700EVKIT
EVAL KIT FOR MAX19700
MAX19985AETX+T
IC MIXER DOWNCONV 36-TQFN-EP
MAX19993ETX+
IC MIXER DOWNCONV 36TQFN
MAX19994AEVKIT#
KIT EVAL FOR MAX19994A MIXER
MAX19995ETX+T
IC DOWNCONVERTER 2CH 36TQFN
MAX19995EVKIT#
EVALUATION KIT FOR MAX19995
MAX19996AEVKIT#
EVALUATION KIT FOR MAX19996A
相关代理商/技术参数
MAX1474AXT
制造商:Maxim Integrated Products 功能描述:MINIATURE ELECTRONICALLY TRIMMABLE CAPACITOR - Rail/Tube
MAX1474AXT+
制造商:Maxim Integrated Products 功能描述:MINIATURE ELECTRONICALLY TRIMMABLE CAP 6PIN SC-70 - Rail/Tube
MAX1474AXT+T
功能描述:整流器/与可变电容器 Mini Electronically Trimmable Cap RoHS:否 制造商:Xicon 电容范围:2.8 pF to 12.5 pF 容差: 电压额定值:200 V 工作温度范围:- 35 C to + 85 C 端接类型:SMD/SMT 产品:Trimmer Capacitors - Ceramic Dielectric
MAX1474AXT-T
制造商:Maxim Integrated Products 功能描述:MINIATURE ELECTRONICALLY TRIMMABLE CAPACITOR - Tape and Reel
MAX1474CXT
制造商:Maxim Integrated Products 功能描述:MINIATURE ELECTRONICALLY TRIMMABLE CAPACITOR - Rail/Tube
MAX14752
制造商:Maxim Integrated Products 功能描述:8-CHANNEL/DUAL 4-CHANNEL 72V ANALOG MUX - Rail/Tube
MAX14752EUE+
功能描述:多路器开关 IC 8:1 72V Analog Mux
RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16
MAX14752EUE+T
功能描述:多路器开关 IC 8:1 72V Analog Mux
RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16